Console:

Changes to previous version
—————————

  • Added support for UCD-424.
  • Added Firmware Update capability over USB.
  • UCD-400, UCD-424: Added SSC support.
  • Added support for HDCP 2.3 facsimile keys.
  • UCD Console: Fixed bug in Pattern generator that caused all error messages to not show up.
  • UCD Console: Fixed bug which caused incorrect H-Active size being sent out from DP TX after disabling DSC.
  • UCD Console: Fixed bug which caused incorrect colorimetry to be used after disabling DSC on DP TX.
  • UCD Console: Fixed issue which caused the Sink DUT DSC test CRC calculations to not properly follow the selected mode.
  • UCD Console: Fixed HPD Event decoding in Event Logger.
  • UCD Console: Removed „From“ and „F“ columns from Event Logger.
  • UCD Console: Removed faulty „From“ column from Event Logger report generator.
  • UCD Console: Fixed an access violation when changing view settings in event logger while capturing.
  • UCD Console: Event logger and AUX Monitor now start timestamps from 0.001 ms.
  • UCD Console: Increased the display timestamp resolution of AUX monitor to 0.001 ms.
  • UCD Console: Fixed bug which allowed selection of YCbCr color formats for motion pattern.
  • UCD Console: Fixed bug with parsing USB-C PD commands in Event Logger.
  • UCD Console: Added 6 New configurations for DSC compression (9 and 11 bpp).
  • UCD Console: Fixed bug that caused AUX transaction directions to be inverted.
  • UCD Console: Fixed bug which caused GUI to lock up if attempting to re-enable MST in pattern generator page with zero streams.
  • UCD Console: Fixed virtual channel numbering on Video- and Audio-preview pages; New numbering starts from 0, which is same as on link page.
  • UCD Console: Fixed issues with DSC CRC calculation with YCbCr 4:4:4
  • UCD Console: DP-RX: Added control for enabling DP_PWR pin to output 3.3V. Note: The DP_PWR control will only appear if the hardware indicates support for it.
  • UCD Console: Added support for setting HDCP Content type.
  • UCD Console: Fixed „Most Packed timing“ selectable values to match better with CTS Specifications in „LL CTS: Source DUT configuration“ dialog.
  • UCD Console: Fixed PD decoder issue which caused partial or corrupted output.
  • UCD Console: Added support for Augemented PDO’s in PD Decoder.
  • UCD Console: Fixed incorrect PDO flags decoding.
  • UCD Console: Fixed bug which prevented HDCP related DPCD registers from being decoded in AUX Analyzer pages.
  • UCD Console: Fixed bug which caused invalid timestamps to be displayed after loading a saved event log from a file after capturing an event log, or after loading another event log file.
  • UCD Console: Fixed bug which caused hang negative timestamps were received from the device.
  • UCD Console: Fixed bug which caused HPD events to move around in AUX analyzer views.
  • UCD Console: Fixed bug which caused event logger to use wrong capture mode on the device, which lead to lost events and instability.
  • UCD Console: Added check for device support when initializing device selector.
  • UCD Console: Fixed bug which caused different colors to appear into AUX Analyzer report files that what was used by the GUI.
  • UCD Console: Changed decoding of HPD events in AUX analyzer view. Multiple HPD change messages to same state should no longer show up.
  • Fixed bug in DSC compression caused by incorrect INITIAL_FULLNESS_OFFSET value.
  • LLCTS. Sink DUT. 5.4.4.5, 5.4.4.6. Added cycle by spread spectrum clocking. Fixed link configuration. 
  • LLCTS. Sink DUT. 5.4.1.4. Enabled spread spectrum clocking.
  • LLCTS. Sink DUT. 5.4.1.3 Fixed EDID parsing for most packed video modes.
  • LLCTS. Sink DUT. Fixed bug which caused voltage swing values to be logged as zero volts. This issues was present in several tests.
  • LLCTS. Source DUT. Test 4.5.1.1. Fixed bug which caused the test to time out if the long HPD pulse was same or longer duration than the test time out.
  • LLCTS. Sink DUT. Test 5.3.1.3. Added error message for the situation where no lanes are flagged as complete for five iterations.
  • LLCTS. Sink DUT. 5.4.4.2 Use video stream at the preferred timing, RGB color bar, 8bpc.
  • LLCTS. Source DUT. 4.2.2.8 Fixed check if Source DUT disables video stream before EDID read.
  • LLCTS. Sink DUT. Fixed mask for I2C_OVER_AUX reply.
  • LLCTS. Sink DUT. Fixed HPD de-assertion check during the time link training is taking place (test 5.3.1.1 and all tests that use steps from 5.3.1.1).
  • LLCTS. Sink DUT. 5.4.4.5 Fixed the incorrect maud dithering setting for RBR 32kHz and 96kHz.
  • LLCTS. Sink DUT. Added check for supported bpc at current link configuration for EDID preferred video mode.
  • LLCTS. Sink DUT. Added EDID validity check to video and audio tests.
  • LLCTS. Sink DUT. 5.2.2.5 Added check for AUX reply length.
  • LLCTS. Sink DUT. 5.3.1.2 + 5.3.1.3 Disable transmitters on required lanes by sending empty data.
  • LLCTS. Sink DUT. Fixed issues with empty log lines and typos.
  • LLCTS. Sink DUT. 5.3.1.2. Fixed check for unexpected CR lock on any active lane, not on all active lanes simultaneously.
  • LLCTS. Sink DUT. 5.3.1.x. Check max_voltage condition only for active lanes.
  • CRC Stability test: Fixed timeout related issues.
  • DP TX: Fixed bug where DP_PWR pin did not output 3.3V.
  • DP TX: Disable FEC and DSC when HPD is low.
  • DP RX: Clear FEC status when HPD is low.
  • DP TX: HDCP: Configuration for HDCP 2.3 of Content Type Value
  • UCD-400, UCD-424; DP TX: Added forced idle output pattern.
  • UCD-323, UCD-301; DP RX: Implemented 3.3V power control.
  • DP RX: Fixed link training failure on cable replug due to missing cable disconnect event.
  • DP TX: Make channel reallocation even if downstream reports no available PBN.
  • LLCTS. Sink DUT. Setting voltage swing and pre-emphasis at the TX transmitters after enabling transmitters to avoid false CR lock.
  • LLCTS. Sink DUT. Changed error numbering to be consistent with the previous release.
  • DP TX: Mute audio generator on power up.
  • LLCTS. Sink DUT. 5.3.1.7 Send all zeroes to stop transmission on all lanes.
  • UCD-400: Fixed incorrect frame rate after first video mode change.
  • LLCTS. Source DUT. DSC: Use Base block preferred timing for all timings up to UHD 60Hz for non YUV 4:2:0.
  • LLCTS. Sink DUT. 5.2.1.7 Read all EDID segments.
  • LLCTS. DSC. Source DUT. Print message that DSC is not required for selected video mode.
  • DPTX. LTTPR. LT. EQ. Use TPS4 for Phy Repeaters and fix selection TP for Sink.
  • LLCTS. Sink DUT. 5.4.1.3 Added check for maximum supported bpc.

TSI:

Changes to previous version
—————————

  • Added support for UCD-1
  • Configuration items added for HDMI Source devices: TSI_SRC_HDMI_SCDC_ADDRESS, TSI_SRC_HDMI_SCDC_DATA.
  • Configuration items added for USB-C Devices: TSI_W_USBC_ROLE_CONTROL_SWAP, TSI_R_USBC_ROLE_CONTROL_SWAP
  • Updated TSI-X Reference manual, section 7.2 for additional scripting features.
  • Added „-prvarabs“ command to print absolute value of a variable
  • „-if“ now works with strings and string variables
  • Addedscripting global variable lastreadarray to access all values read from a configuration item. This means -saveread need no longer be used.

www.unigraf.fi/downloads/
www.dimedtec.de/downloads/Unigraf/UCD/

Quelle: Unigraf

    Schlagwörter: , , , ,